It is unlikely that both Motors (Drive Motor – Ref.# 1.15 and Pump Motor – Ref.# 1.14) are experiencing mechanical problems. In most cases the issue lies with something that is hindering the flow of electricity from the electrical outlet to the Power Supply (Figure 4) or through the Floating Cable (Ref.# 3.1) to the Aquabot itself. To locate and resolve where electrical flow is being hindered check the following.
With electrical power cords going underwater. It's more likely to be a replacement than a 'repair'. I'd recommend calling Aquabot. See if they can sell you a replacement cord. If they can, than you'll also need to determine whether this is a repair you can tackle, or one that will require a factory authorized agent. Aquabot Bravo Features and Specs. This is an in ground pool robot, probably should have brought that up earlier. It limits its utility a little, but I think the majority of us with pools have an. MerCruiser Repair Manual 454 & 502 7.4L/8.2L. 1998-2002 MerCruiser Repair Manual D7.3L V8 Diesel. 1998-2003 MerCruiser Repair Manual 3.0L. 2000-2008 MerCruiser Repair Manual D1.7L DTI. 2000-2005 MerCruiser Repair Manual Bravo & Sport. DOWNLOAD MERCRUISER ENGINE & STERNDRIVE REPAIR MANUALS Aquabot Bravo Manual Please carefully. Aquabot dragon parts; eagle parts; embassy pool parts; mirage parts; reaction parts; aquabot spirit parts; pool town's pool shark parts; bravo parts; flame parts; fury parts; viva parts; aquabot service center. Click here for aquabot home service; dolphin cleaners and parts. Dolphin cleaners; dolphin parts; dolphin service center. 15 - SCREW S/S #8X11/16 PHIL PAN (LARGE HEAD, FOR SIDE PLATE AND DRIVE MOTOR) 51110: Aqua Products 2700: $2.36: Place Order $.
Aquabot Bravo Manual
Electrical Outlet & Connections – Make sure that the Power Supply is firmly plugged into a grounded electrical outlet which has power. To test the outlet, plug in another electrical instrument that you know works to the outlet.
Check that the Floating Cable is securely plugged into the Power Supply.
Power Supply
- Check that the Power Supply button is pressed upwards to the “ON” position. Note: Some models have a Reset (Safety) Switch, which must be pressed each time you press the “ON” button.
- Switch the Power Supply “Off” and “On” several times, allowing approximately 30 seconds between each“ON” and “OFF”. Remember, if your Aquabot comes equipped with a Reset Switch it must be pressed each time after pressing the “ON” button.
- Unplug the Power Supply from the electrical outlet. Check that the Fuse in the Power Supply’s Fuse Holder (Ref.# 4.4) appears operational. If the Fuse appears burned out, then replace it with a 5 AMP SLO BLOW Fuse Please note that there are various Power Supply model types and the location of the Fuse may be in either the front or the back of your Power Supply.
- Use a cotton swab to dry all sides of the Fuse and Fuse Holder (inside and out). Cable Assemblies – With the Power Supply unplugged, check the Power Cable (Ref.# 4.6) and the Floating Cable for cuts or damage. If you detect damage to either Cable, please contact our Customer Service Department at 1-800-845-4856.
Battleship Movie Download In Tamilrockers
Aquabot Parts And Manuals
If you want to add new locations to check for installation files, provide them here. Installation source registry key. ) Look for the following values to edit as needed: • Installation Sources (REG_MULTI_SZ): This lists all of the possible locations for Windows to check for installation files, each on its own line. (Note that in Windows 2000, the Registry path may use 'Windows NT' instead of 'Windows.' Windows keeps its installation source locations in the Registry key HKEY_LOCAL_MACHINE SOFTWARE Microsoft Windows CurrentVersion Setup. If you install with one and then try to add components with the other, Windows may not be able to find everything if you use SFC.